| Result pages: |
1 |
2 |
 |
|
See details
|
PECO PL-10E TURNOUT MOTOR WITH EXTENED OPERATINGE PIN
The PL10-E point motor is fitted with a long point operating pin, ideal for mounting beneath baseboards. A small 10mm (3/8in) hole through the baseboard is required, located directly beneath the operating pin attachment location on the point. The pin will then reach through the board and locate into the operating pin attachment hole of the point. The pin can then be trimmed to length with a good side or track cutter tool. Peco strongly recommend that the PL10E be used in conjunction with a PL-9 Mounting Plate, fitted directly to the base board underneath the point. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers (2 amps required). If this isn't available an uncontrolled 12v DC supply may suffice. A constant current would burn out the motor.
Our price: AUD$14.99
|
|
See details
|
PECO PL-10W TURNOUT MOTOR FOR LOW AMPERAGE APLLICATIONS
This point motor is designed to operate with the lower amperage found on some European transformers or with DCC systems*. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers. If this isn't available an uncontrolled 12v DC supply may suffice. A constant current would burn out the motor.
* Although the initial amperage from DCC systems is very high, say 10 amps, the final amps avaialble to accessories such as point motors is very low, once the current has passed through the booster units used in DCC systems.
Current draw approx 1.5amps
Our price: AUD$16.95
|
|
See details
|
PECO PL-11 SIDE MOUNTED TURNOUT MOTOR
Designed to clip into the side of a Setrack or Streamline OO/HO code 100 turnout. This motor alleviates the need for making holes below the baseboard. The non-intrusive design of the sealed unit sits neatly alongside the turnout.
Suitable for either right hand or left hand turnout.
Our price: AUD$24.95
|
|
See details
|
PECO PL-12X MOTOR ADAPTOR BASE
If above baseboard fitting is essential the Peco Turnout Motor can be mounted using this Adaptor Base. Extension arm included.
PL-12 has been superseeded to PL-12X.
Our price: AUD$3.99
|
|
See details
|
PECO PL-13 ACCESSORY SWITCH
Simple, inexpensive switch easily fitted underneath the Turnout Motor (PL-10) to provide electrical switching for frog polarity, signals, etc.
Suitable only for OO/HO and larger scales.
Rated 1.5 Amps
Our price: AUD$7.99
|
|
See details
|
PECO PL-15 TWIN MICRO SWITCH KIT
For fitting to Turnout Motor PL-10.
Easy to assemble unit with two microswitches to control the polarity of live frogs whilst simultaneously operating panel indicator lights.
Complete with illustrated instructions
Rated 2.5 Amps
Our price: AUD$19.95
|
|
See details
|
PECO PL-34 WIRING LOOM
Ideal for wiring up Peco point motors quickly and easily these wiring looms provide an 18-inch (450mm) wiring lead with spade connectors which fit directly to the contacts on the side of the Peco point motors.
Pack of 2 looms.
Our price: AUD$12.95
|
|
See details
|
PECO PL-35 CAPACITOR DISCHARGE UNIT
•A CDU Gives A Split Second Power Boost The To The Point Motor When You Actually Operate It.
•Requires 12 Volt DC or 16 Volt AC input.
•One Unit Should Be Powerful Enough For The Average Layout.
Our price: AUD$39.95
|
|
See details
|
PECO PL-40 WHEEL CLEANING BRUSH & SCRAPER
Essential for cleaning locomotive driving wheels to ensure efficient running.
Simply connect the wires from the Brush & Scraper direct to 12 Volts DC power source and apply the Brush and Scraper to the driving wheels, one each side.
Pack Contains 1 pc each.
Our price: AUD$24.99
|
|
See details
|
PECO PL-50 TURNOUT SWITCH MODULE
Peco Modular Quick Connect Bracket for PL26 Switches
A new design of switch mouting bracket incorporting wire connection clips for quick connection of point motor wiring. The PL26 switches plug in to the bracket, eliminating the need to solder connections.
Our price: AUD$49.95
|
|
See details
|
PECO PL-51 SWITCH MODULE ADD ON
Peco Modular Quick Connect Bracket Extension for PL26 Switches
A new design of switch mouting bracket incorporting wire connection clips for quick connection of point motor wiring. The PL26 switches plug in to the bracket, eliminating the need to solder connections.
Our price: AUD$15.99
|
|
See details
|
PECO PL-64 POWER LUBE
Power-Lube is the successor to ‘Electrolube’. It has been made for PECO by the famous Electrolube manufacturer to a new formula, safe to use with most modern plastics used in models nowadays. The Power-Lube container comes complete with a long, thin nozzle for easy application.
Our price: AUD$14.95
|
|
|
